Page 1 of 11 Product: Bona Classic Issue Date: 10th February 2023 Revision: 3.0 SAFETY DATA SHEET SECTION 1 – IDENTIFICATION: PRODUCT IDENTIFIER/CHEMICAL IDENTITY 1.1 PRODUCT IDENTIFIER: Bona Classic 1.2 PRODUCT CODE: Not applicable. 1.3 RELEVANT IDENTIFIED USES OF THE MIXTURE AND USES ADVISED AGAINST: RELEVANT IDENTIFIED USES: Waterborne finish for timber floors. RESTRICTIONS ON USE: None known. 1.4 DETAILS OF THE SUPPLIER OF THE SAFETY DATA SHEET: SUPPLIER NAME: Bona Australia Pty Ltd (ABN: 2208 758 1520), ADDRESS: Unit 9, Wareca Business Park 1866 Princes Highway, Clayton, Victoria, 3168 E-MAIL: info@bona.com.au TELEPHONE NUMBER: 03 9543 4399 1.5 EMERGENCY TEL. NUMBER: 03 9543 4399 Business Hours. (0408 008 762 After Hours or National Chemical Emergency Centre Europe 18000 74234.) Poisons Information Centre (Aust 131 126) SECTION 2 – HAZARD(S) IDENTIFICATION 2.1 CLASSIFICATION OF THE HAZARDOUS CHEMICAL: GHS CLASSIFICATION HAZARD CLASS & CATEGORY: Under the Model Work Health and Safety Regulations, the product would not be classified as hazardous. 2.2 LABEL ELEMENTS INCLUDING PRECAUTIONARY STATEMENTS: SIGNAL WORD: Not Applicable. PICTOGRAMS: Not Applicable. HAZARD STATEMENTS: Not Applicable. PRECAUTIONARY STATEMENTS: PREVENTION: P102 - Keep out of reach of children. P103 - Read carefully and follow all instructions. RESPONSE: P101 - If medical advice is needed, have product container or label at hand. STORAGE: Not Applicable. DISPOSAL: Not Applicable. 2.3 OTHER HAZARDS: The mixture has a low order of toxicity associated with it. May cause mild gastric irritation if swallowed. Excessive exposure may result in mild irritation to the skin or respiratory system as well as possible irritation to the eye. People with pre-existing skin conditions, such as eczema or dermatitis, should take precautions so as not to exacerbate the condition. As for all chemical products, persons should not expose open wounds, cuts, abrasions or irritated skin to this material. SECTION 3 – COMPOSITION / INFORMATION ON INGREDIENTS INGREDIENTS CAS NUMBER Concentration GHS % W/W Classification* Propanol, (2-methoxymethylethoxy)- (Dipropylene glycol, monomethyl ether) 34590-94-8 < 3% Not Applicable Non-hazardous ingredients - To 100% Not Applicable * Please see Section 15 of this SDS for the full text description of the Label Elements. Page 2 of 11 Product: Bona Classic SAFETY DATA SHEET SECTION 4 – FIRST AID MEASURES 4.1 DESCRIPTION OF NECESSARY FIRST AID MEASURES: INGESTION: Rinse mouth out with water. If swallowed, according to the manufacturer, do NOT induce vomiting. For advice, contact the Poisons Information Centre (phone Australia 131 126; New Zealand 0800 764 766) or a doctor. If vomiting occurs, lean patient forward or place on left side (head-down position, if possible) to maintain open airway and prevent aspiration. If irritation develops or persists or vomiting has occurred after ingestion, seek medical assistance. EYE: If in eyes, hold eyelids apart and flush the eye immediately with large amounts of running water. Continue flushing for at least 15 minutes or until advised to stop by a doctor. Check for contact lenses. If there are contact lenses, these should be removed after several minutes of rinsing by the exposed person or medical personnel if it can be done easily. After flushing, if irritation develops or persists, seek medical assistance. SKIN CONTACT: If skin or hair contact has occurred remove any contaminated clothing and footwear, wash skin or hair thoroughly with soap and water. Do NOT use solvents and/or thinners. If irritation develops or persists, consult a doctor. INHALATION: If affected, remove the patient from further exposure into fresh air, if safe to do so. If providing assistance, avoid exposure to yourself - only enter contaminated environments with adequate respiratory equipment. Once removed, lay patient down in a well-ventilated area and reassure them whilst waiting for medical assistance. If not breathing, provide artificial respiration and seek immediate medical assistance. If unconscious, place in a recovery position and seek immediate medical assistance. If irritation develops/persists, consult a doctor. PROTECTION FOR FIRST AIDERS: No personnel shall place themselves in a situation that is potentially hazardous to themselves. Assess the environment for PPE requirements before entering. Do not enter contaminated area without a respirator. As the product is a floor coating, if the person has ingested the product, do not use direct mouth-to-mouth resuscitation techniques. Always ensure that you are wearing gloves when dealing with first aid procedures involving chemicals and/or blood. FIRST AID FACILITIES: Eye wash fountain and safety showers are recommended in the area where the product is used. As a minimum, a source of running, potable water must be available. 4.2 MOST IMPORTANT SYMPTOMS & EFFECTS, BOTH ACUTE & DELAYED, CAUSED BY EXPOSURE: ACUTE: Ingestion or inhalation of vapours may lead to irritation of the mouth and respiratory tract. Ingestion may lead to nausea. Eye contact may lead to localised burning, redness and tearing. Skin contact may lead to redness or itching. CHRONIC: Repeated or prolonged skin contact may also aggravate/exacerbate existing skin conditions, such as dermatitis. 4.3 INDICATION OF ANY IMMEDIATE MEDICAL ATTENTION AND SPECIAL TREATMENT NECESSARY: ADVICE TO DOCTOR: Treat symptomatically. The manufacturer recommends that if large quantities have been ingested or inhaled a Poisons Specialists should be contacted immediately as a precaution. Page 3 of 11 Product: Bona Classic SAFETY DATA SHEET SECTION 5 – FIRE FIGHTING MEASURES 5.1 EXTINGUISHING MEDIA: SUITABLE MEDIA: Use extinguishing media appropriate for surrounding fire. Use carbon dioxide, alcohol resistant foam, dry chemical or water fog. Spray down fumes resulting from fire. UNSUITABLE MEDIA: Avoid using full water jet directed at residual material that may be burning. Water may cause splattering on hot residues. 5.2 SPECIAL HAZARDS ARISING FROM THE SUBSTANCE OR MIXTURE: COMBUSTION HAZARDS: If the solvent is evaporated during a fire, combustion of the residual components may produce oxides of carbon and nitrogen, as well as smoke and irritating vapours. 5.3 ADVICE FOR FIREFIGHTERS: FIRE: This product is not flammable under conditions of use. Once the solvent component has evaporated, the residual component will be combustible. Keep storage areas and fire exposed surfaces, etc, cool with water spray. Do not allow runoff from a fire to enter drains, sewers or waterways. HAZCHEM CODE: Not applicable. EXPLOSION: No information to indicate that the product is an explosion hazard. Extinguish all sources of flame or spark. Closed containers may explode when exposed to extreme heat. PROTECTIVE EQUIPMENT: In the event of a fire, wear full protective clothing and self-contained breathing equipment with full-face piece operated in the pressure demand or other positive pressure mode. SECTION 6 – ACCIDENTAL RELEASE MEASURES 6.1 PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES: PERSONAL PROTECTION:For spills, wear Nitrile Rubber gloves, glasses/goggles, boots and full-length clothing. During routine operation for a small spill a respirator is not required. However, if mists or vapours are generated, an approved organic vapour/particulate respirator is required. For large spills, or in confined spaces, a full chemically resistant body-suit is recommended and the atmosphere must be evaluated for oxygen deficiency. If in doubt wear self-contained breathing apparatus. CONTROL MEASURES: Ventilate area and extinguish and/or remove all sources of ignition. Stop the leak if safe to do so. Caution: The spilled product will be slippery. Avoid contact with the spilled material. EMERGENCY PROCEDURES: In the event of a spill or accidental release, notify the relevant authorities in accordance with all applicable regulations. 6.2 ENVIRONMENTAL PRECAUTIONS: SPILL ADVICE: Do not allow product to enter drains, surface water, sewers or watercourses - inform local authorities if this occurs. Page 4 of 11 Product: Bona Classic SAFETY DATA SHEET SECTION 6 – ACCIDENTAL RELEASE MEASURES - Continued 6.3 METHODS AND MATERIALS FOR CONTAINMENT AND CLEANING UP: CONTAINMENT: Contain the spill and absorb with a proprietary absorbent material, sand or earth. Caution: The spilled product will be slippery. For large spills prepare a bund/barrier/dyke ahead of the spill to confine the spill and allow later recovery. If there is the possibility of spills to enter drains, surface water, sewers or watercourses ensure bunding, or that drains are covered, to minimise the potential for this to occur. CLEANING PROCEDURES: Having contained the spill, as mentioned above, collect all material quickly and place used absorbent in suitable containers. Caution: The spilled product will be slippery. Follow local regulations for the disposal of waste. For large spills that have been bunded, the material can be pumped into vessels and returned for reprocessing or destruction. Personnel must wear gloves, goggles or glasses, boots and full-length clothing during cleaning procedures. Wash contaminated area and objects with detergent and water after spill has been cleared. Rinse the cleaned area with water. Do not allow wash water or rinsings to enter drains, surface water, sewers or water courses. Avoid using solvents during the cleaning process. SECTION 7 – HANDLING AND STORAGE, INCLUDING HOW THE CHEMICAL MAY BE SAFELY USED 7.1 PRECAUTIONS FOR SAFE HANDLING: SAFE HANDLING: Avoid contact with the product by using appropriate protective equipment such as gloves, glasses or goggles and full-length clothing. A full-face shield should be used if there is the potential for the product to enter the eye via processes such as mixing or splashes. Prevent small spills and leakage to avoid slip hazards. Eating, drinking, and smoking should be prohibited in the area where this material is handled, stored and processed. Workers should follow good personal hygiene practices, such as washing hands before eating, drinking and smoking. Remove contaminated clothing and protective equipment before entering eating areas. Avoid inhalation of vapours; as per any industrial product adequate ventilation must be supplied to remove vapours from the work environment to achieve this. Always keep in containers made of the same material as the original one. Never use pressure to empty the container; the container is not a pressure vessel. Keep containers tightly closed when not in use. Prevent product from entering waterways, drains or sewers. 7.2 CONDITIONS FOR SAFE STORAGE, INCLUDING ANY INCOMPATABILITIES: SAFE STORAGE: Store in a dry, well ventilated, frost-free area away from direct sunlight, ignition sources, oxidising agents, strong acids and alkalis, foodstuffs, animal feeds and clothing. Keep containers closed when not in use. Always keep in containers made of the same material as the original one. Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Protect the packaging from damage. When the packaged material is intact the product is deemed to be of limited hazard. INCOMPATIBILITIES: Avoid oxidising agents, including strong acids, and strongly alkaline materials. Page 5 of 11 Product: Bona Classic SAFETY DATA SHEET SECTION 8 – EXPOSURE CONTROLS & PERSONAL PROTECTION 8.1 EXPOSURE CONTROL MEASURES: EXPOSURE LIMIT VALUES: Exposure standards for the product have not been established. However, in the operation of certain equipment or at elevated temperatures, if Dipropylene glycol, monomethyl ether vapours or mists are generated, the following Exposure Standard must be observed: Dipropylene glycol, monomethyl ether (Skin annotation): Time Weighted Average (TWA): 50 ppm, 308 mg/m3 8.2 BIOLOGICAL MONITORING: No data available. 8.3 CONTROL BANDING: No data available. 8.4 ENGINEERING CONTROLS: ENGINEERING CONTROLS: Use product in a well ventilated area. Where reasonably practical this should be achieved by the use of local exhaust ventilation and good general extraction. Special ventilation is not normally required. However, in the operation of certain equipment, in enclosed spaces or at elevated temperatures, mists or vapours may be generated and exhaust ventilation may be required to maintain airborne concentration levels below the exposure standard or below a level considered irritating by individuals. 8.5 INDIVIDUAL PROTECTION MEASURES: EYE & FACE PROTECTION: Wear safety glasses/goggles to avoid eye contact. If when mixing or stirring the product there is the possibility of splashing, a full-face shield is recommended. Use eye protection in accordance with AS 1336 and AS 1337. SKIN (HAND) PROTECTION: If there is the chance of skin contact with the material; wear gloves to provide hand protection. Nitrile rubber gloves are recommended. Gloves should be replaced regularly. SKIN (CLOTHING) PROTECTION: During normal operating procedures, long sleeved clothing is recommended to avoid skin contact. Soiled clothing should be washed with detergent prior to re-use. RESPIRATORY PROTECTION: Use only in well-ventilated areas. During routine operation, a respirator is not required. If mists or vapours are generated, an approved half face organic vapour/particulate respirator is required. Dry sanding, grinding, flame/heat stripping and cutting of the dry film will give rise to dust and/or hazardous fumes. Wet sanding/flatting should be used wherever possible. If exposure cannot be avoided by the provision of local exhaust ventilation during such operations, suitable respiratory protective equipment, such as an approved half face organic vapour/particulate respirator is required. Use respirators in accordance with AS 1715 and AS 1716. THERMAL PROTECTION: Not applicable. Page 6 of 11 Product: Bona Classic SAFETY DATA SHEET SECTION 9 – PHYSICAL AND CHEMICAL PROPERTIES 9.1 PHYSICAL AND CHEMICAL PROPERTIES: APPEARANCE: White liquid. ODOUR: No data available. ODOUR THRESHOLD: No data available. pH: Typically 8. MELTING/FREEZING POINT: No data available. INITIAL BOILING POINT: No data available. BOILING RANGE (oC): No data available. FLASHPOINT (oC): > 100oC (Note: The product does not sustain combustion.). EVAPORATION RATE: No data available. FLAMMABILITY LIMITS (%): No data available. VAPOUR PRESSURE (kPa): No data available. VAPOUR DENSITY: No data available. DENSITY (g/mL @ 20oC): Typically 1.04. SOLUBILITY IN WATER(g/L): Soluble in water. PARTITION COEFFICIENT: No data available for n-octanol/water. AUTO-IGNITION TEMP (oC): No data available. DECOMPOSITION TEMP (oC): No data available. VISCOSITY (Dynamic): No data available. VISCOSITY (cSt @ 40oC): No data available. SECTION 10 – STABILITY AND REACTIVITY 10.1 REACTIVITY: The product does not pose any further reactivity hazards other than those listed in the following sub-sections. 10.2 CHEMICAL STABILITY: Stable under recommended storage and handling conditions (see section 7). 10.3 POSSIBILITY OF HAZARDOUS REACTIONS: Keep away from strong oxidising agents, including strong acids and strong alkalis. Hazardous polymerisation does not occur. 10.4 CONDITIONS TO AVOID: Observe the usual precautionary measures for handling chemicals. Do not heat the container or leave the container open when not in use. 10.5 INCOMPATIBLE MATERIALS: Avoid oxidising agents, strong acids and strong alkaline materials. 10.6 HAZARDOUS DECOMPOSITION PRODUCTS: Hazardous decomposition products are not expected to form during normal storage requirements. See Section 5.2 for Hazardous Combustion products. SECTION 11 – TOXICOLOGICAL INFORMATION 11.1 INFORMATION ON TOXICOLOGICAL EFFECTS: The product is a mixture and test data is not available for the product as a whole. The following component data is supplied by the manufacturer: Dipropylene glycol, monomethyl ether Oral - LD50 (Rat): 5,130 mg/kg Dermal - LD50 (Rabbit): 9,500 mg/kg Page 7 of 11 Product: Bona Classic SAFETY DATA SHEET SECTION 11 – TOXICOLOGICAL INFORMATION - Continued 11.2 SWALLOWED: This product is expected to have a low order of toxicity associated with it when ingested. Ingestion may cause slight irritation to the mouth, throat and digestive tract. Ingestion of significant quantities may lead to irritation to the stomach and the person may feel nauseous. As the product is a floor coating product, aspiration into the lungs may be an issue if vomiting has occurred after ingestion or if stomach irrigation is deemed necessary. If the product is ingested and the person has vomited, they should be observed to ensure there is no aspiration into the lungs. During normal usage, ingestion should not be a means of exposure. 11.3 SKIN CORROSION / IRRITATION: This product is not expected to exhibit Dermal Corrosivity/Irritation, based on the available data and the known hazards of the components. May be mildly irritating to the skin. The Dipropylene glycol, monomethyl ether constituent has the Skin Annotation assigned to it. This means absorption through the skin may be a significant source of exposure. Prolonged or repeated contact may cause removal of the natural fat from the skin, resulting in non-allergic contact dermatitis and possibly absorption through the skin. Correct handling procedures incorporating appropriate protective clothing and gloves should minimise the risk of skin irritation. People with pre-existing skin conditions, such as dermatitis, should take extreme care so as not to exacerbate the condition. According to the Manufacturer Dipropylene glycol, monomethyl ether in rabbit studies is a mild irritant. 11.4 SERIOUS EYE DAMAGE / IRRITATION: This product is not expected to exhibit Eye Irritation or Serious Damage/ Corrosivity, based on the available data and the known hazards of the components according to the manufacturer. May be mildly irritating to the eyes. Symptoms may include localised burning, redness and tearing. Correct handling procedures incorporating appropriate eye protection should minimise the risk of eye irritation. According to the Manufacturer Dipropylene glycol, monomethyl ether in rabbit and human studies is a mild irritant. 11.5 RESPIRATORY OR SKIN SENSITISATION: This product is not expected to be a skin sensitiser, based on the available data and the known hazards of the components. This product is not expected to be a respiratory tract sensitiser, based on the available data and the known hazards of the components. 11.6 GERM CELL MUTAGENICITY: This product is not expected to be mutagenic based on the available data and the known hazards of the components. 11.7 CARCINOGENICITY: This product is not expected to be a carcinogen based on the available data and the known hazards of the components. 11.8 REPRODUCTIVE TOXICITY: This product is not expected to be a reproductive hazard based on the available data and the known hazards of the components. 11.9 SPECIFIC TARGET ORGAN TOXICITY (STOT) – SINGLE EXPOSURE: This product is not expected to cause organ damage from a single exposure, based on the available data and the known hazards of the components. This product is not expected to pose an irritation hazard at ambient temperature or under normal handling conditions. Not classified as a respiratory irritant, however inhalation of vapours or mist (generated at elevated temperatures or by mechanical action) may cause irritation to the nose, throat and respiratory system. Page 8 of 11 Product: Bona Classic SAFETY DATA SHEET SECTION 11 – TOXICOLOGICAL INFORMATION - Continued 11.10 SPECIFIC TARGET ORGAN TOXICITY (STOT) – REPEATED EXPOSURE:This product is not expected to cause organ damage from prolonged or repeated exposure, based on the available data and the known hazards of the components. 11.11 ASPIRATION HAZARD: This product is not expected to be an aspiration hazard, based on the available data and the known hazards of the components. As the product is a floor coating product, aspiration into the lungs may be an issue if vomiting has occurred after ingestion or if stomach irrigation is deemed necessary. As a precaution, if vomiting has occurred after ingestion, the patient should be monitored for adverse effects. 11.12 OTHER INFORMATION: No additional information available. SECTION 12 – ECOLOGICAL INFORMATION 12.1 ECOTOXICITY: There is no data available for the product as a whole. According to the manufacturer, the product has been assessed following the summation method of the CLP Regulation (EC) No 1272/2008 and is not classified as hazardous to the environment. The following Acute Toxicity data has been provided for the components: Dipropylene glycol, monomethyl ether EC50 (Daphnia, 48 hrs): 1,919 mg/L LC50 (Algae, 96 hrs): > 969 mg/L LC50 (Fish, 96 hrs): > 10,000 mg/L 12.2 PERSISTENCE & DEGRADABILITY: No persistence or biodegradability data is available for the product. The manufacturer nominates that Dipropylene glycol, monomethyl ether is readily degradable. 12.3 BIOACCUMULATIVE POTENTIAL: No bioaccumulative data is available for the product. The manufacturer nominates that Dipropylene glycol, monomethyl ether has a Log Pow of 0.004 and has a low potential for bioaccumulation. 12.4 MOBILITY IN SOIL: No information is available. 12.5 OTHER ADVERSE EFFECTS: Do not allow product to enter drains, surface water, sewers or watercourses - inform local authorities if this occurs. The product is miscible with water. SECTION 13 – DISPOSAL CONSIDERATIONS 13.1 DISPOSAL METHODS: PRODUCT: The product should not be released to the environment, so any unused material should be recycled wherever possible or be disposed of as waste at an appropriate collection depot. Spilled product that cannot be recovered should be absorbed and then shovelled into a suitable waste container, such as a plastic drum and then be treated as a solid waste. Follow Government regulations for disposal of such waste. All unused, waste or spilled product must be taken for recycling or disposal by suitably licensed contractors in accordance with Government regulations. Do not pour leftover product down the drain. Unwanted material should be brushed out on newspaper, allowed to dry and then disposed of via normal domestic or industrial waste collection. Page 9 of 11 Product: Bona Classic SAFETY DATA SHEET SECTION 13 – DISPOSAL CONSIDERATIONS - Continued CONTAINERS: Empty containers may contain residual material. They should be completely drained and then stored until reconditioned or disposed of. Empty containers should be taken for recycling or disposal through suitably licensed contractors in accordance with Government regulations. Empty containers should be recycled wherever possible rather than being sent to landfill or incinerated. If being sent to landfill any residual product must be allowed to dry/cure before disposal. SECTION 14 – TRANSPORT INFORMATION This product is not regulated for land, sea or air transportation. 14.1 LAND (ADG Code): UN NUMBER: Not applicable UN PROPER SHIPPING NAME: Not applicable TRANSPORT HAZARD CLASS(ES): Not applicable PACKAGING GROUP: Not applicable ENVIRONMENTAL HAZARDS: Not applicable SPECIAL PRECAUTIONS FOR USER: Not applicable HAZCHEM CODE: Not applicable 14.2 SEA (IMDG): UN NUMBER: Not applicable UN PROPER SHIPPING NAME: Not applicable TRANSPORT HAZARD CLASS(ES): Not applicable PACKAGING GROUP: Not applicable ENVIRONMENTAL HAZARDS: Not applicable SPECIAL PRECAUTIONS FOR USER: Not applicable 14.3 AIR (IATA): UN NUMBER: Not applicable UN PROPER SHIPPING NAME: Not applicable TRANSPORT HAZARD CLASS(ES): Not applicable PACKAGING GROUP: Not applicable ENVIRONMENTAL HAZARDS: Not applicable SPECIAL PRECAUTIONS FOR USER: Not applicable SECTION 15 – REGULATORY INFORMATION 15.1 SAFETY, HEALTH AND ENVIRONMENTAL REGULATIONS: APPLICABLE REGULATIONS: SUSMP: Not scheduled. AIIC: All ingredients are on the AIIC List. MONTREAL PROTOCOL: Not applicable to this product. STOCKHOLM CONVENTION: Not applicable to this product. ROTTERDAM CONVENTION: Not applicable to this product. BASEL CONVENTION: Not applicable to this product. INTERNATIONAL CONVENTION FOR THE PREVENTION OF POLLUTION FROM SHIPS (MARPOL): Not applicable to this product. OTHER REGULATORY INFORMATION: GHS CLASSIFICATION HAZARD CLASS & CATEGORY AND HAZARD STATEMENT: Not applicable. Page 10 of 11 Product: Bona Classic SAFETY DATA SHEET SECTION 16 – ANY OTHER RELEVANT INFORMATION SDS INFORMATION: Date of SDS Preparation: 10th February 2023 Revision: 3.0 REVISION CHANGES: Five year review and update of SDS for compliance. ACRONYMS: SUSMP Standard for the Uniform Scheduling of Medicines and Poisons CAS Number Chemical Abstracts Service Registry Number EINECS European Inventory of Existing Commercial Chemical Substances UN Number United Nations Number OSHA Occupational Safety and Health Administration ACGIH American Conference of Governmental Industrial Hygienists HSE-WEL Health and Safety Executive - Workplace Exposure Limit EH40 EH40/2005 Workplace Exposure Limits IMDG International Maritime Dangerous Goods IATA International Air Transport Association IUCLID International Uniform Chemical Information Database RTECS Registry of Toxic Effects of Chemical Substances %W/W Percent weight for weight OECD Organisation for Economic Co-Operation and Development ADG Code Australian Code for the Transport of Dangerous Goods by Road and Rail HAZCHEM Code Emergency action code of numbers and letters which gives information to emergency services NOHSC National Occupational Health and Safety Commission AICIS Australian Industrial Chemicals Introduction Scheme IMAP Inventory Multi-Tiered Assessment and Prioritisation AIIC Australian Inventory of Industrial Chemicals TWA Time-Weighted Average STEL Short Term Exposure Limit HSNO Hazardous Substances and New Organisms Act 1996 GHS Globally Harmonised System of Classification and Labelling of Chemicals WHS Work Health and Safety PPE Personal Protective Equipment. LD50 Median Lethal Dose LC50 Median Lethal Concentration EC50 Effective Concentration of a substance that causes 50% of the maximum response after exposure for a nominated time ECHA European Chemicals Agency REACH Registration, Evaluation, Authorisation and Restriction of Chemicals HCIS Hazardous Chemical Information System PBT Persistent, Bioaccumulative and Toxic vPvP Very Persistent and Very Bioaccumulative LITERATURE REFERENCES AND SOURCES OF DATA: OECD Guidelines for Testing of Chemicals Annex I: OECD Test Guidelines for Studies Included in SIDS Manual for the Assessment of Chemicals Chapter 2 Data Gathering International Toxicity Testing Guidelines Hazardous Chemical Information System (HCIS) - Guidance Material for Hazard Classifications Preparation of Safety Data Sheets for Hazardous Chemicals Code of Practice. Model Work Health and Safety Regulations. Model Work Health and Safety Regulations - Transitional Principles Workplace Exposure Standards for Airborne Contaminants Australian Dangerous Goods Code 7th Edition Approved Criteria for Classifying Hazardous Substances [NOHSC:1008 (2004)] Guidance on the Classification of Hazardous Chemicals under the WHS Regulations Assigning a Hazardous Substance to a Group Standard User Guide to the HSNO Thresholds and Classifications Summary User Guide to the HSNO Thresholds and Classifications of Hazardous Substances Page 11 of 11 Product: Bona Classic SAFETY DATA SHEET SECTION 16 – ANY OTHER RELEVANT INFORMATION - Continued LITERATURE REFERENCES AND SOURCES OF DATA: (Continued) Correlation between GHS and New Zealand HSNO Hazard Classes and Categories HSNO Control Regulations Record of Group Standard Assignment Labelling of Hazardous Substances Hazard and Precautionary Information Thresholds and Classifications Under the Hazardous Substances and New Organisms Act 1996 Workplace Exposure Standards and Biological Exposure Indices All information contained in this Safety Data Sheet and the health, safety and environmental information are considered to be accurate to the best of our knowledge as of the issue date specified above. The information presented here within, is based upon the product information supplied by the manufacturer. However, no warranty or representation, expressed or implied, is made as to the accuracy or completeness of the data and information contained in this data sheet. Health and safety precautions and environmental advice noted in this data sheet may not be accurate for all individuals and/or situations. It is the user’s obligation to evaluate and use this product safely and to comply with all applicable laws and regulations. The Company accepts no responsibility for any injury, loss or damage, resulting from abnormal use of the material, from any failure to adhere to recommendations, or from any hazards inherent in the nature of the material.